Any spoke calculator you find on the internet will require you to enter some information. Just how much information depends on the web site’s spoke calculator and the popularity of the components of your wheel. Popular rims and hubs can often be chosen from a list. For these, the needed values will be provided with the exception of the number of spoke holes and the number of crosses your spokes will be laced with.

Having to measure for the needed values isn’t the end of the world. Some of the web sites will help you through the measurements but you will need a sliding caliper and a tape measure to get those measurements.

Here are some spoke calculators and information about wheel building you may find useful.

DT Swiss This happens to be my favorite, probably because it’s the easiest. Sign in as an anonymous user.

Sheldon Brown

spokelength.com

United Bicycle Institute

wheelpro.co.uk

appliedthought.com Great instructions!

Good luck building!

I wish I could count all the flat tires I fixed during the week, I’m sure the number would be in the hundreds, as I’m positive I did over 20 a day. The miles my left arm pedaled as I shifted through bikes’ gears also took it’s toll. By the time the riders reached L.A., my arms were weak and useless.

The amount of tubes that got thrown away along the route was unfortunate. I wish I had the ability to at least get them recycled, but transporting thousands of bike tubes would require some special arrangements. Maybe next year we could make those arrangements, or maybe have a contest to find creative uses for the tubes that won’t hold air. The crowd that rides the AIDS Lifecycle is a creative bunch and I’m sure the contest would be a hit and produce some entertaining results.

Second only to flat tires, worn pedal cleats plagued many riders, some multiple times during the week. The cyclists wearing mountain bike shoes with walkable cleats were laughing at the riders with road bike shoes waiting in line for new $20 cleats. Cannondale’s technical support team had a hard time fulfilling the need for Look Delta, Look Keo, and Shimano SPD R cleats for the poor soles(pun) that didn’t have cleat covers to walk around in.

All in all, a great week playing with bicycles. The faces I recognized from last year were great to see again, and I hope to see this year’s new acquaintances next year. I hope everyone heeds my warning and brings there mountain bike shoes and pedals, but I’ll certainly be there to change your worn cleats out for you. See you then.

Product description:

A new book on bike repair from the company that wrote the book on bike repair products. Calvin Jones, Education Director at Park Tool, provides easy-to-follow, step-by-step instructions for keeping any road or mountain bike running smoothly. From tire repair and derailleur adjustment to wheel truing and bottom bracket replacement, The Big Blue Book of Bike Repair provides both the novice and veteran mechanic with the information needed to perform nearly any repair. Special topics such as tool selection, bike cleaning, and on-the-trail repairs are also covered, and an appendix at the back of the book provides valuable reference materials. Up to date with the latest technology, The Big Blue Book of Bike Repair is packed four hundred photos, as well as repair tips garnered from the author’s 30 years as an educator and mechanic.

A great book to keep in the tool box or next to the bed. Buy it here.

From pcschools.us:

Save time, money, and maybe a trip to the bike shop! Keep your bicycle running smoothly and safely. Learn the proper way to clean and lube your bicycle, basic fit, basic maintenance, and emergency repair. Bring your bike to this hands-on class. Tool list provided in class, plus information on where to ride. Both road and mountain bikes are welcome. Limit of 10 people.

Registration and More Info

As my web progress moves at a snails pace, I can see the dedication and time he must have put into sheldonbrown.com. Millions have benefited. Thanks Sheldon, I really dug your style.

Sheldon Brown July 14, 1944-February 3, 2008

Yesterday I received any early birthday gift in the form of a fresh, still in the packaging, Crank Bros. Multi 17 Tool in the mail.  It took a mere 17 days for the process and only cost me the price of the original tool plus $1.58 for shipping back to the company.  My new tool even has a snazzier finish than the one I sent back.

In conclusion, I highly recommend  the Multi 17 for many reasons.  Besides being your friend in your time of need on your bike, it offers a lifetime warranty that Crank Brothers has proved to me to stand behind.  All that in a tool in the $10 ballpark, that’s pretty sweet.  Buy one here.

In order to understand what you’re about to read, you’ll need a quick lesson in pedal and bike anatomy. First thing first, whenever referring to right or left on a bicycle, it’s as if you were sitting on the saddle of the bicycle with your hands on the handlebar. Therefore the right side of the bike generally has the drivetrain( derailleurs, gears, and chain). I say “generally” because there are some exceptions. Disc brake calipers are typically mounted to the left side of a bicycle. You get the idea. The center of the bike is a plane that would split the rider, tires, and frame, perpendicular to the ground.

The pedals thread into the right and left crank arms. The large threaded part of the pedal is the pedal spindle, some times called a pedal axle. The part of the pedal that contacts your foot is the pedal body. The pedal body spins on the spindle with the help of bushings or bearings, and a bit of grease. The pedal spindle will have the wrench surfaces that dictate what type of wrench you should use.

The proper pedal wrench is dependent on the pedals on the bike, and more specifically what the pedal spindle has been designed to be compatible with. The most common pedal wrench is probably the 15mm open ended wrench which works on pedals that have wrench flats on the spindle, between the crank arm and the pedal body. There are also pedals that use a similar 9/16″ wrench. The 9/16″ and the 15mm are close in size and appearance and care should be taken to use the proper wrench, especially if your pedal wrench offers both. If the pedal is designed to be used with a hex pedal wrench, the hex socket is found at the end of the spindle, on the inside of the crank arm. These hex sockets on the pedals will be either 6mm or 8mm. Whichever style wrench the pedal is designed to accept, be sure to use a wrench designed specifically for pedals! It will make life easier.

Before you begin the installation, place the bicycle in a stable position. A bike repair stand is best, but leaning it against a wall or flipping it upside down will do just fine. Next, clean the threads on the cranks and the pedals. Once the surfaces are clean you can apply a small amount of bicycle grease to the pedal threads. The grease will help combat corrosion, noise, and seizing, making the pedal’s removal easier later.

Pedals are left and right specific and deciding which is which can be accomplished through a few ways. If there are an L(for left) and an R(for right) stamped into the pedal spindle consider yourself lucky and move on to the next step. Sometimes just one pedal will be stamped with the distinguishing L or R, so check both. If a pedal has a toe clip, is one sided, or is a directional pedal, there is only one direction the pedals can be mounted and remain functional. Hold the pedals up to the bicycle to figure out which is right and left. You can grab your cycling shoes to check how the shoe attaches to the pedal in a clipless pedal and shoe system if you aren’t sure. If none of those work for your situation, hold the pedal up in front of you. Hold the pedal by the pedal body with the spindle pointing threaded end up. The threads on the spindle will appear to have a high and a low side. If the threads run up and to the left, it’s the left pedal. If the threads run up and to the right, it’s the right pedal. Holding both pedals next to each other can make picking up the slight slope of the threads easier on your eyes.

Getting the pedal threads started can be the toughest challenge of the whole process. Sometimes it’s so challenging I will go back to check if I am trying to install the correct side pedal. Double checking is always good too. You’ll want to use your finger to get the pedal started into the crank. By using your fingers you have more control and a better feel in order to get the threads started. Cross threading is a term for what occurs when you thread something in crooked. It is very bad in the world of pedals and cranks. Finger starting the pedals doesn’t allow you enough force on the pedal to mis form the metal threads.

To install the right pedal hold the pedal spindle perpendicular to the right crank so that it lines up with the threaded hole in the crank. Turning the pedal spindle to the right, or clockwise, while holding it in the proper position will start the pedal threads. Use one hand to hold the pedal body to stabilize while the other hand turns the pedal spindle. Got that? To the right. Install the right pedal by turning the spindle to the right(clockwise).

To install the left pedal use the same two handed technique as with the right. The only difference is the left pedal has a left thread, or reverse thread. That means you’ll have to install the left pedal by turning the pedal spindle to the left(counter clockwise). This is opposite of what we are used to as our standard threads are righty tighty. Left pedal, left thread. Left pedal, left thread. Left pedal, left thread.

A couple more thoughts on pedal installation. If you can’t get a pedal started and you are positive it’s the correct side, you may need to re tap the thread to clean them. Threads can easily be damaged. Most shops will have pedal taps and the job is usually quick and easy. About your pedal wrench, it is designed with a long handle for making pedal removal easier if the pedal has been overtightened. The long handle is not to overtighten the pedals. You do not want them to come loose, but you’ll probably want to get them off some day. If you aren’t sure what the proper torque for your pedals are, check with a professional mechanic for some help. Good luck.

In order to understand what you’re about to read, you’ll need a quick lesson in pedal and bike anatomy. First thing first, whenever referring to right or left on a bicycle, it’s as if you were sitting on the saddle of the bicycle with your hands on the handlebar. Therefore the right side of the bike generally has the drivetrain( derailleurs, gears, and chain). I say “generally” because there are some exceptions. Disc brake calipers are typically mounted to the left side of a bicycle. You get the idea. The center of the bike is a plane that would split the rider, tires, and frame, perpendicular to the ground.

The pedals thread into the right and left crank arms. The large threaded metal part of the pedal is the pedal spindle, some times called a pedal axle. The part of the pedal that contacts your foot is the pedal body. The pedal body spins on the spindle with the help of bushings or bearings, and a bit of grease. The pedal spindle will have the wrench surfaces that dictate what type of wrench you should use.

The proper pedal wrench is dependent on the pedals on the bike, and more specifically what the pedal spindle has been designed to be compatible with. The most common pedal wrench is probably the 15mm open ended wrench which works on pedals that have wrench flats on the spindle, between the crank arm and the pedal body. There are also pedals that use a similar 9/16″ wrench. The 9/16″ and the 15mm are close in size and appearance and care should be taken to use the proper wrench, especially if your pedal wrench offers both. If the pedal is designed to be used with a hex pedal wrench, the hex socket is found at the end of the spindle, on the inside of the crank arm. These hex sockets on the pedals will be either 6mm or 8mm. Whichever style the pedal is designed to accept, be sure to use a wrench designed specifically for pedals! It will make life easier.

A couple more things before you remove that pedal. Shift your chain up to the big chain ring(outermost). By covering the teeth on that chain ring you can help avoid the occasional blood letting that goes with pedal removal. I’ve even started to wear my mechanic’s gloves(cheap rubberized gardening gloves) all the time because I’m sick of bloody knuckles. The point is, be careful.

As I like things to be easy, I recommend positioning the bike so it’s stable, while offering you both hands free to work. A bike repair stand would be best, but leaning it against a wall, or even flipping it upside down will do just fine.

Pedals are left and right specific. Because the pedals are on the bike, it’s fairly easy to tell which pedal is left and which is right. Let’s start with the right pedal. The right pedal will unthread from the crank as the spindle turns counter clockwise. When you place the pedal wrench on the wrench flats or in the hex socket be sure keep the angle between the wrench and the crank arm less than 90 degrees. The advantage gained by proper wrench position is crucial as pedals are often victim to severe over tightening. See pics below.

These photos show two different kinds of pedal wrenches at an angle less than 90 degrees to the crank.

Use one hand to help steady the bike or hold the opposite crank arm for more leverage. Grasping the pedal wrench at the end of the handle, apply force in the counter clockwise direction. Many pedals will have a noticeable threshold between tight and loose, but some will require brute force throughout the removal of the pedal. Consider the right pedal removed

The left pedal will be removed the same way, except the wrench will need to be turned clockwise. The left pedal has a left thread, also called a reverse thread. The left hand thread is opposite of what most would consider the standard or a righty tighty thread. Therefore in removal of the left pedal, force must be applied to the wrench in a clockwise direction. Once you can remember that the left pedal has a left thread, you are ruling pedal removal. Left pedal, left thread. Left pedal, left thread. Left pedal, left thread.

That’s it. These helping hints should lead you to easy pedal removal.

I think shopping for the average bicycle mechanic may be easier than shopping for the average person. Typically bike mechanics are broke leaving lots of room for need and want in an industry that has excess gadgetry and changing technology.

$0.01-$10
tubes
gear cleaning brush
valve caps

$10-$25
digital air gauge
folding multi tool
bike porn
beer glasses
Big Blue Book of Bike Repair

$25+
Ultimate hanging bike scale
messenger bag
safety glasses
frame building school
air compressor
torque wrench

Crank Brothers claims a lifetime warranty on their tools. I didn’t see any fine print associated with that statement, but who knows? I will be returning the tool without all of the parts and with a healthy amount of rust. The letter I will include with the crippled tool will go something like this.:

Dear Crank Brothers,

I broke my Multi 17 tool while trying to remove an overtightened pedal at the end of a ride. I realize the task could have used a tool better suited, but my Multi 17 was all I had on hand.

I’ve already purchased another multi 17 to replace this one, but maybe you could help me out with a backup.

Love your new line.

Thanks,

KC

I’ll send the tool and letter on Monday 11/26 and keep you posted on how it goes. For more info on Crank Brothers, check out their website at www.crankbrothers.com or visit TPW Marketplace for killer deals on their products.