It’s time to install some pedals on a bike. If you are in possession of a pedal wrench and some bike grease, you are ready to tackle the pedal installation. No need to run to the local bike shop.

In order to understand what you’re about to read, you’ll need a quick lesson in pedal and bike anatomy. First thing first, whenever referring to right or left on a bicycle, it’s as if you were sitting on the saddle of the bicycle with your hands on the handlebar. Therefore the right side of the bike generally has the drivetrain( derailleurs, gears, and chain). I say “generally” because there are some exceptions. Disc brake calipers are typically mounted to the left side of a bicycle. You get the idea. The center of the bike is a plane that would split the rider, tires, and frame, perpendicular to the ground.

The pedals thread into the right and left crank arms. The large threaded part of the pedal is the pedal spindle, some times called a pedal axle. The part of the pedal that contacts your foot is the pedal body. The pedal body spins on the spindle with the help of bushings or bearings, and a bit of grease. The pedal spindle will have the wrench surfaces that dictate what type of wrench you should use.

The proper pedal wrench is dependent on the pedals on the bike, and more specifically what the pedal spindle has been designed to be compatible with. The most common pedal wrench is probably the 15mm open ended wrench which works on pedals that have wrench flats on the spindle, between the crank arm and the pedal body. There are also pedals that use a similar 9/16″ wrench. The 9/16″ and the 15mm are close in size and appearance and care should be taken to use the proper wrench, especially if your pedal wrench offers both. If the pedal is designed to be used with a hex pedal wrench, the hex socket is found at the end of the spindle, on the inside of the crank arm. These hex sockets on the pedals will be either 6mm or 8mm. Whichever style wrench the pedal is designed to accept, be sure to use a wrench designed specifically for pedals! It will make life easier.

Before you begin the installation, place the bicycle in a stable position. A bike repair stand is best, but leaning it against a wall or flipping it upside down will do just fine. Next, clean the threads on the cranks and the pedals. Once the surfaces are clean you can apply a small amount of bicycle grease to the pedal threads. The grease will help combat corrosion, noise, and seizing, making the pedal’s removal easier later.

Pedals are left and right specific and deciding which is which can be accomplished through a few ways. If there are an L(for left) and an R(for right) stamped into the pedal spindle consider yourself lucky and move on to the next step. Sometimes just one pedal will be stamped with the distinguishing L or R, so check both. If a pedal has a toe clip, is one sided, or is a directional pedal, there is only one direction the pedals can be mounted and remain functional. Hold the pedals up to the bicycle to figure out which is right and left. You can grab your cycling shoes to check how the shoe attaches to the pedal in a clipless pedal and shoe system if you aren’t sure. If none of those work for your situation, hold the pedal up in front of you. Hold the pedal by the pedal body with the spindle pointing threaded end up. The threads on the spindle will appear to have a high and a low side. If the threads run up and to the left, it’s the left pedal. If the threads run up and to the right, it’s the right pedal. Holding both pedals next to each other can make picking up the slight slope of the threads easier on your eyes.

Getting the pedal threads started can be the toughest challenge of the whole process. Sometimes it’s so challenging I will go back to check if I am trying to install the correct side pedal. Double checking is always good too. You’ll want to use your finger to get the pedal started into the crank. By using your fingers you have more control and a better feel in order to get the threads started. Cross threading is a term for what occurs when you thread something in crooked. It is very bad in the world of pedals and cranks. Finger starting the pedals doesn’t allow you enough force on the pedal to mis form the metal threads.

To install the right pedal hold the pedal spindle perpendicular to the right crank so that it lines up with the threaded hole in the crank. Turning the pedal spindle to the right, or clockwise, while holding it in the proper position will start the pedal threads. Use one hand to hold the pedal body to stabilize while the other hand turns the pedal spindle. Got that? To the right. Install the right pedal by turning the spindle to the right(clockwise).

To install the left pedal use the same two handed technique as with the right. The only difference is the left pedal has a left thread, or reverse thread. That means you’ll have to install the left pedal by turning the pedal spindle to the left(counter clockwise). This is opposite of what we are used to as our standard threads are righty tighty. Left pedal, left thread. Left pedal, left thread. Left pedal, left thread.

A couple more thoughts on pedal installation. If you can’t get a pedal started and you are positive it’s the correct side, you may need to re tap the thread to clean them. Threads can easily be damaged. Most shops will have pedal taps and the job is usually quick and easy. About your pedal wrench, it is designed with a long handle for making pedal removal easier if the pedal has been overtightened. The long handle is not to overtighten the pedals. You do not want them to come loose, but you’ll probably want to get them off some day. If you aren’t sure what the proper torque for your pedals are, check with a professional mechanic for some help. Good luck.

Pedals need to be removed for various reasons. Travel, shipment, pedal replacement, pedal service, or maybe your selling a bike and you just want your pedals back. In any case, it’s not always so convenient to run down to the local bike shop. If you are in possession of the proper tools, this task can be handled easily without going anywhere.

In order to understand what you’re about to read, you’ll need a quick lesson in pedal and bike anatomy. First thing first, whenever referring to right or left on a bicycle, it’s as if you were sitting on the saddle of the bicycle with your hands on the handlebar. Therefore the right side of the bike generally has the drivetrain( derailleurs, gears, and chain). I say “generally” because there are some exceptions. Disc brake calipers are typically mounted to the left side of a bicycle. You get the idea. The center of the bike is a plane that would split the rider, tires, and frame, perpendicular to the ground.

The pedals thread into the right and left crank arms. The large threaded metal part of the pedal is the pedal spindle, some times called a pedal axle. The part of the pedal that contacts your foot is the pedal body. The pedal body spins on the spindle with the help of bushings or bearings, and a bit of grease. The pedal spindle will have the wrench surfaces that dictate what type of wrench you should use.

The proper pedal wrench is dependent on the pedals on the bike, and more specifically what the pedal spindle has been designed to be compatible with. The most common pedal wrench is probably the 15mm open ended wrench which works on pedals that have wrench flats on the spindle, between the crank arm and the pedal body. There are also pedals that use a similar 9/16″ wrench. The 9/16″ and the 15mm are close in size and appearance and care should be taken to use the proper wrench, especially if your pedal wrench offers both. If the pedal is designed to be used with a hex pedal wrench, the hex socket is found at the end of the spindle, on the inside of the crank arm. These hex sockets on the pedals will be either 6mm or 8mm. Whichever style the pedal is designed to accept, be sure to use a wrench designed specifically for pedals! It will make life easier.

A couple more things before you remove that pedal. Shift your chain up to the big chain ring(outermost). By covering the teeth on that chain ring you can help avoid the occasional blood letting that goes with pedal removal. I’ve even started to wear my mechanic’s gloves(cheap rubberized gardening gloves) all the time because I’m sick of bloody knuckles. The point is, be careful.

As I like things to be easy, I recommend positioning the bike so it’s stable, while offering you both hands free to work. A bike repair stand would be best, but leaning it against a wall, or even flipping it upside down will do just fine.

Pedals are left and right specific. Because the pedals are on the bike, it’s fairly easy to tell which pedal is left and which is right. Let’s start with the right pedal. The right pedal will unthread from the crank as the spindle turns counter clockwise. When you place the pedal wrench on the wrench flats or in the hex socket be sure keep the angle between the wrench and the crank arm less than 90 degrees. The advantage gained by proper wrench position is crucial as pedals are often victim to severe over tightening. See pics below.

These photos show two different kinds of pedal wrenches at an angle less than 90 degrees to the crank.

Use one hand to help steady the bike or hold the opposite crank arm for more leverage. Grasping the pedal wrench at the end of the handle, apply force in the counter clockwise direction. Many pedals will have a noticeable threshold between tight and loose, but some will require brute force throughout the removal of the pedal. Consider the right pedal removed

The left pedal will be removed the same way, except the wrench will need to be turned clockwise. The left pedal has a left thread, also called a reverse thread. The left hand thread is opposite of what most would consider the standard or a righty tighty thread. Therefore in removal of the left pedal, force must be applied to the wrench in a clockwise direction. Once you can remember that the left pedal has a left thread, you are ruling pedal removal. Left pedal, left thread. Left pedal, left thread. Left pedal, left thread.

That’s it. These helping hints should lead you to easy pedal removal.

Gift shopping is a double edged sword for me. While getting someone that perfect present is satisfying, the aggravation in extensive searching, or even worse, the certainty that the recipient won’t appreciate it and will probably give it away next holiday season, can leave one feeling not so good. Hopefully these tips will save you some time and effort, at the same time providing the bike mechanic with something they’ll want.

I think shopping for the average bicycle mechanic may be easier than shopping for the average person. Typically bike mechanics are broke leaving lots of room for need and want in an industry that has excess gadgetry and changing technology.

$0.01-$10
tubes
gear cleaning brush
valve caps

$10-$25
digital air gauge
folding multi tool
bike porn
beer glasses
Big Blue Book of Bike Repair

$25+
Ultimate hanging bike scale
messenger bag
safety glasses
frame building school
air compressor
torque wrench

Let’s do an experiment. Let’s see what happens when I send a mangled Multi 17 tool back to Crank Brothers for warranty. Over all, I’m already sold on the Crank Brothers products. Their pedals, tools, and now various other components, are pleasing to the eye and functional to boot As I’ll mention in my letter to Crank Brothers, I broke my Multi 17 trying to remove an over tightened pedal. That sort of task can be tough with the proper tool. Besides the failure in extreme circumstance, my Multi 17 was a trooper. The chain tool is not so easy to use, but adequate in a pinch. The rest is just what you need for any everyday mountain bike ride, and not too much to slip into your jersey pocket for a long road ride.

Crank Brothers claims a lifetime warranty on their tools. I didn’t see any fine print associated with that statement, but who knows? I will be returning the tool without all of the parts and with a healthy amount of rust. The letter I will include with the crippled tool will go something like this.:

Dear Crank Brothers,

I broke my Multi 17 tool while trying to remove an overtightened pedal at the end of a ride. I realize the task could have used a tool better suited, but my Multi 17 was all I had on hand.

I’ve already purchased another multi 17 to replace this one, but maybe you could help me out with a backup.

Love your new line.

Thanks,

KC

I’ll send the tool and letter on Monday 11/26 and keep you posted on how it goes. For more info on Crank Brothers, check out their website at www.crankbrothers.com or visit TPW Marketplace for killer deals on their products.